Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to auto locksmiths with experience who have the appropriate tools and know-how. They can create and program keys faster and less expensive than dealers.
If your key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. However, there are many other reasons the key could be malfunctioning.
Dead Coin Battery
A dead coin battery can stop your Peugeot 208 from locking or unlocking, and will not start the engine. If this is the situation, you'll need use the backup starting method that is described in the owner's manual to your vehicle.
Another reason why your 208 might not start is that the spark plugs have been worn down. The spark plugs are responsible to ignite the fuel that starts the engine. They only last for a certain amount of time. They will eventually break down when they aren't used enough.
Luckily, there is an easy solution for this issue. Examine the voltage of your battery using a multimeter. If it is below 11.5 volts, then you need to replace it. It is also essential to clean the battery's contacts in case it is corroded. This can be done by taking off the rubber covers from the two battery terminals, and then using a wirebrush to eliminate any corroded battery parts. Then, you must reconnect the positive and negative pole cables.
Water Damage
If your 208 doesn't start and the battery hasn't been replaced, you must check the spark plugs. It is possible that they're dirty, causing them to not to spark. The spark plugs can be cleaned in an workshop.
Peugeot cars have a transponder style key that works with the car's immobiliser system. This ensures that only the right key is able to turn the engine. If the chip in the Peugeot key is damaged then it will not transmit the proper signal to the vehicle.
Water damage is a typical reason for this issue. This is most common in colder climates where the vehicle might have been exposed to rain or snow. In this case, contact a reliable locksmith who has the tools and equipment needed to change the key's programming. They will also have all the latest technology and machinery required to make the Peugeot smart key. The process should take no more than 15 minutes.
Faulty battery contacts
Peugeot changed from the old carbon-encased transponder chips and introduced a new type of chip that incorporates electronic components in a circuit board. The new system is effective when it's fresh, however, over time, the circuit boards start to lose their effectiveness and cease working correctly.
This can prevent the immobiliser chip from activating the immobiliser chip, causing your car not to start. If this is the case it's a good idea seek out a Peugeot specialist or locksmith.
The most frequent issue is when the battery inside the key fob starts to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a new blade for you, it's normally a quick fix.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, getting exposed to a sudden rain or accidently washing it, it could be due to a defective receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer that controls the central locking system in your Peugeot vehicle.
The rubber seals on the key fob keep water from getting to the electronic chip. However prolonged exposure to water could break through these seals, causing damage to the chip. Submerging the key fob in ocean water at the beach or throwing it into the pool could be particularly damaging due to the high salt content.
If your Peugeot spare key fob stops working it is necessary to have the module replaced. This should be done by an Peugeot specialist or expert auto locksmith. Peugeot keys like other cars are secured by an immobilizer system. This requires the proper coding to start the car. It is for this reason that you should only rely on a Peugeot locksmith to create and program a replacement.
Computer on board is not working properly
The on-board computer in your Peugeot is responsible for a variety of systems in your car, including airbags and power windows. The on-board computer will show a code when something goes wrong. The code will be stored within the system until the problem is fixed. This will often require the on-board computers to be replaced.
The most typical reason for the warning light of the airbag to illuminate is corrosion or loose connections in the sensor. This can be caused by wear and tear, aging, or exposure to salt and moisture. It is imperative to have this issue addressed as quickly as possible, since the airbag malfunctioning could be risky in the event of an accident.
If you encounter a card not found error on your Peugeot key fob, the battery in the key fob could be dead or weak. just click the up coming post can prevent the key fob from sending a signal that disarms your vehicle's standard immobilizer. Try this by pressing the unlock key on the key fob, and then trying to start your car. If this doesn't work, then the key battery needs to be replaced.